Controlled degradation of polycaprolactone-based micropillar arrays.

Herein we demonstrate the fabrication of arrays of micropillars, achieved through the combination of direct laser writing and nanoimprint lithography. By combining two diacrylate monomers, polycaprolactone dimethacrylate (PCLDMA) and 1,6-hexanediol diacrylate (HDDA), two copolymer formulations that, owing to the varying ratios of the hydrolysable ester functionalities present in the polycaprolactone moiety, can be degraded in the presence of base in a controllable manner. As such, the degradation of the micropillars can be tuned over several days as a function of PCLDMA concentration within the copolymer formulations, and the topography greatly varied over a short space of time, as visualised using scanning electron microscopy and atomic force microscopy. Crosslinked neat HDDA was used as a control material, demonstrating that the presence of the PCL was responsible for the ability of the microstructures to degrade in the controlled manner. In addition, the mass loss of the crosslinked materials was minimal, demonstrating the degradation of microstructured surfaces without loss of bulk properties was possible. Moreover, the compatibility of these crosslinked materials with mammalian cells was explored. The influence of both indirect and direct contact of the materials with A549 cells was assessed by profiling indices reflective of cytotoxicity such as morphology, adhesion, metabolic activity, oxidative balance, and release of injury markers. No significant changes in the aforementioned profile were observed in the cells cultured under these conditions for up to 72 h, with the cell-material interaction suggesting these materials may have potential in microfabrication contexts towards biomedical application purposes.

The UCD nanosafety workshop (03 December 2018): towards developing a consensus on safe handling of nanomaterials within the Irish university labs and beyond - a report.

Careful handling of the nanomaterials (NMs) in research labs is crucial to ensure a safe working environment. As the largest university in Ireland, University College Dublin (UCD) has invested significant resources to update researchers working with NMs. Due to sizes often <100 nm, the NMs including nanoparticles, harbor unprecedented materialistic properties, for example, enhanced reactivity, conductivity, fluorescence, etc. which albeit conferring the NMs an edge over bulk materials regarding the applied aspects; depending on the dose, also render them to be toxic. Thus, a set of regulatory guidelines have emerged regarding safe handling of the NMs within occupational set-ups. Unfortunately, the current regulations based on the toxic chemicals and carcinogens are often confusing, lack clarity, and difficult to apply for the NMs. As a research-intensive university, a diverse range of research activities occur within the UCD labs, and it is difficult, at times impossible, for the UCD Safety, Insurance, Operational Risk & Compliance (SIRC) office to develop a set of common guidelines and cater throughout all its labs conducting research with the NMs. Hence, a necessity for dialog and exchange of ideas was felt across the UCD which encouraged the researchers including early stage researchers (e.g. PhDs, Postdocs) from multiple schools to participate in a workshop held on the 03 December 2018. The workshop tried to follow a pragmatic approach, where apart from discussing both the in vitro and in vivo scenarios, practical cases simulating situations faced frequently in the labs were discussed. This report summarizes the findings made during the workshop by this emerging critical mass in UCD.

Mechanisms of Polymer-Templated Nanoparticle Synthesis: Contrasting ZnS and Au.

We combine solution small-angle X-ray scattering (SAXS) and high-resolution analytical transmission electron microscopy (ATEM) to gain a full mechanistic understanding of substructure formation in nanoparticles templated by block copolymer reverse micelles, specifically poly(styrene)-block-poly(2-vinylpyridine). We report a novel substructure for micelle-templated ZnS nanoparticles, in which small crystallites (∼4 nm) exist within a larger (∼20 nm) amorphous organic-inorganic hybrid matrix. The formation of this complex structure is explained via SAXS measurements that characterize in situ for the first time the intermediate state of the metal-loaded micelle core: Zn(2+) ions are distributed throughout the micelle core, which solidifies as a unit on sulfidation. The nanoparticle size is thus determined by the radius of the metal-loaded core, rather than the quantity of available metal ions. This mechanism leads to particle size counterintuitively decreasing with increasing metal content, based on the modified interactions of the metal-complexed monomers in direct contrast to gold nanoparticles templated by the same polymer.

Modular and Versatile Spatial Functionalization of Tissue Engineering Scaffolds through Fiber-Initiated Controlled Radical Polymerization.

Native tissues are typically heterogeneous and hierarchically organized, and generating scaffolds that can mimic these properties is critical for tissue engineering applications. By uniquely combining controlled radical polymerization (CRP), end-functionalization of polymers, and advanced electrospinning techniques, a modular and versatile approach is introduced to generate scaffolds with spatially organized functionality. Poly-ε-caprolactone is end functionalized with either a polymerization-initiating group or a cell-binding peptide motif cyclic Arg-Gly-Asp-Ser (cRGDS), and are each sequentially electrospun to produce zonally discrete bilayers within a continuous fiber scaffold. The polymerization-initiating group is then used to graft an antifouling polymer bottlebrush based on poly(ethylene glycol) from the fiber surface using CRP exclusively within one bilayer of the scaffold. The ability to include additional multifunctionality during CRP is showcased by integrating a biotinylated monomer unit into the polymerization step allowing postmodification of the scaffold with streptavidin-coupled moieties. These combined processing techniques result in an effective bilayered and dual-functionality scaffold with a cell-adhesive surface and an opposing antifouling non-cell-adhesive surface in zonally specific regions across the thickness of the scaffold, demonstrated through fluorescent labelling and cell adhesion studies. This modular and versatile approach combines strategies to produce scaffolds with tailorable properties for many applications in tissue engineering and regenerative medicine.